[En-Nut-Discussion] how to program the ethernut

[Klemen Dovrtel]

I tried pe0 and pe1 with ponyprog and it works. Thank
you!

--- Klemen Dovrtel <klemen_dovrtel at yahoo.com> wrote:

> This isp doesn't support ATmega128.
> I found this on your link: "Most of the AVR chips
> use
> MOSI and MISO signalsbut the MEGA103 uses PE0 for
> MOSI
> and PE1 for MISO. The rest signals SCK and RESET,
> are
> the same." Why is that? Is this the same for
> ATmega128?
> 
> --- Thiago A. Corrêa <thiago.correa at gmail.com>
> wrote:
> 
> > Hi,
> > 
> >    Sorry for the delay. Here, I´m using this one:
> >
>
http://www.iready.org/projects/uinternet/ispdongle.pdf
> >    Here you will find where to connect the output
> in
> > the chip pins:
> >
>
http://chaokhun.kmitl.ac.th/~kswichit/STK300/Stk300.html
> > 
> > 
> > On 11/26/05, Franck
> <ethernut-user_chat at ulukai.net>
> > wrote:
> > > Hi,
> > >
> > > could you send your scheme on the list, and the
> > correct one after checking
> > > on the list too, because I'm planning to use
> > ponyprog to program my charon2
> > > module.
> > >
> > > Thanks
> > >
> > > +-----Message d'origine-----
> > > +De : en-nut-discussion-bounces at egnite.de
> > > +[mailto:en-nut-discussion-bounces at egnite.de]De
> la
> > part de Klemen Dovrtel
> > > +Envoyé : samedi 26 novembre 2005 12:51
> > > +À : Ethernut User Chat (English)
> > > +Objet : Re: [En-Nut-Discussion] how to program
> > the ethernut
> > > +
> > > +
> > > +uC=microcontroller
> > > +Ponyprog is ok, i can program atmega8.
> > > +Would you please send me the scheme of
> programmer
> > you
> > > +use.
> > > +Best regards
> > > +
> > > +--- Thiago A. Corrêa <thiago.correa at gmail.com>
> > wrote:
> > > +
> > > +> I don't know what is uC, but a locked
> processor
> > does
> > > +> read "something"
> > > +> in the ponyprog, it reads some garbage data,
> > but
> > > +> doesn't give you
> > > +> "device not found". I do know that it is a
> bit
> > hard
> > > +> to setup pony, it
> > > +> had issues with many pcs where I work...
> > something
> > > +> with the LPT that I
> > > +> can't quite figure out. One thing I always do
> > is set
> > > +> it to ECC+EPP in
> > > +> the bios, seams to work sometimes. Also, my
> > working
> > > +> machine has the
> > > +> LPT1 in 0x378, that info might be helpfull.
> > > +>
> > > +> I don't have the scheme for the programmer
> I'm
> > using
> > > +> right now, but I
> > > +> can send you a link on monday if you want, we
> > built
> > > +> ours with some
> > > +> spare parts, not hard to assemble :)
> > > +>
> > > +> On 11/25/05, Klemen Dovrtel
> > > +> <klemen_dovrtel at yahoo.com> wrote:
> > > +> > I connected the vcc, gnd, miso, mosi, sck
> and
> > rst
> > > +> (i
> > > +> > removed r22 and added r34) to my ponyprog
> > > +> programmer
> > > +> > and try to read data from uC, but i get an
> > error
> > > +> > (device missing). I am shure that the
> > connsetions
> > > +> are
> > > +> > ok, and the programmer is ok. The ethernut
> > board
> > > +> is
> > > +> > new. Why is that? Is the uC locked?
> > > +> >
> > > +> >
> > > +> >
> > > +> > __________________________________
> > > +> > Yahoo! Music Unlimited
> > > +> > Access over 1 million songs. Try it free.
> > > +> > http://music.yahoo.com/unlimited/
> > > +> >
> > _______________________________________________
> > > +> > En-Nut-Discussion mailing list
> > > +> > En-Nut-Discussion at egnite.de
> > > +> >
> > > +>
> > >
> >
>
+http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> > > +> >
> > > +>
> _______________________________________________
> > > +> En-Nut-Discussion mailing list
> > > +> En-Nut-Discussion at egnite.de
> > > +>
> > >
> >
>
+http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> > > +>
> > > +
> > > +
> > > +
> > > +
> > > +
> > > +__________________________________
> > > +Yahoo! Mail - PC Magazine Editors' Choice 2005
> > > +http://mail.yahoo.com
> > > +_______________________________________________
> > > +En-Nut-Discussion mailing list
> > > +En-Nut-Discussion at egnite.de
> > >
> >
>
+http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> > > +
> > >
> > > _______________________________________________
> > > En-Nut-Discussion mailing list
> > > En-Nut-Discussion at egnite.de
> > >
> >
>
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> > >
> > _______________________________________________
> > En-Nut-Discussion mailing list
> > En-Nut-Discussion at egnite.de
> >
>
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> > 
> 
> 
> 
> 	
> 		
> __________________________________ 
> Yahoo! Mail - PC Magazine Editors' Choice 2005 
> http://mail.yahoo.com
> _______________________________________________
> En-Nut-Discussion mailing list
> En-Nut-Discussion at egnite.de
>
http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> 



	
		
__________________________________ 
Yahoo! Mail - PC Magazine Editors' Choice 2005 
http://mail.yahoo.com