[En-Nut-Discussion] how to program the ethernut

[Thiago A. Corrêa]

Hi,

   Sorry for the delay. Here, I´m using this one:
http://www.iready.org/projects/uinternet/ispdongle.pdf
   Here you will find where to connect the output in the chip pins:
http://chaokhun.kmitl.ac.th/~kswichit/STK300/Stk300.html


On 11/26/05, Franck <ethernut-user_chat at ulukai.net> wrote:
> Hi,
>
> could you send your scheme on the list, and the correct one after checking
> on the list too, because I'm planning to use ponyprog to program my charon2
> module.
>
> Thanks
>
> +-----Message d'origine-----
> +De : en-nut-discussion-bounces at egnite.de
> +[mailto:en-nut-discussion-bounces at egnite.de]De la part de Klemen Dovrtel
> +Envoyé : samedi 26 novembre 2005 12:51
> +À : Ethernut User Chat (English)
> +Objet : Re: [En-Nut-Discussion] how to program the ethernut
> +
> +
> +uC=microcontroller
> +Ponyprog is ok, i can program atmega8.
> +Would you please send me the scheme of programmer you
> +use.
> +Best regards
> +
> +--- Thiago A. Corrêa <thiago.correa at gmail.com> wrote:
> +
> +> I don't know what is uC, but a locked processor does
> +> read "something"
> +> in the ponyprog, it reads some garbage data, but
> +> doesn't give you
> +> "device not found". I do know that it is a bit hard
> +> to setup pony, it
> +> had issues with many pcs where I work... something
> +> with the LPT that I
> +> can't quite figure out. One thing I always do is set
> +> it to ECC+EPP in
> +> the bios, seams to work sometimes. Also, my working
> +> machine has the
> +> LPT1 in 0x378, that info might be helpfull.
> +>
> +> I don't have the scheme for the programmer I'm using
> +> right now, but I
> +> can send you a link on monday if you want, we built
> +> ours with some
> +> spare parts, not hard to assemble :)
> +>
> +> On 11/25/05, Klemen Dovrtel
> +> <klemen_dovrtel at yahoo.com> wrote:
> +> > I connected the vcc, gnd, miso, mosi, sck and rst
> +> (i
> +> > removed r22 and added r34) to my ponyprog
> +> programmer
> +> > and try to read data from uC, but i get an error
> +> > (device missing). I am shure that the connsetions
> +> are
> +> > ok, and the programmer is ok. The ethernut board
> +> is
> +> > new. Why is that? Is the uC locked?
> +> >
> +> >
> +> >
> +> > __________________________________
> +> > Yahoo! Music Unlimited
> +> > Access over 1 million songs. Try it free.
> +> > http://music.yahoo.com/unlimited/
> +> > _______________________________________________
> +> > En-Nut-Discussion mailing list
> +> > En-Nut-Discussion at egnite.de
> +> >
> +>
> +http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> +> >
> +> _______________________________________________
> +> En-Nut-Discussion mailing list
> +> En-Nut-Discussion at egnite.de
> +>
> +http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> +>
> +
> +
> +
> +
> +
> +__________________________________
> +Yahoo! Mail - PC Magazine Editors' Choice 2005
> +http://mail.yahoo.com
> +_______________________________________________
> +En-Nut-Discussion mailing list
> +En-Nut-Discussion at egnite.de
> +http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
> +
>
> _______________________________________________
> En-Nut-Discussion mailing list
> En-Nut-Discussion at egnite.de
> http://www.egnite.de/mailman/listinfo.cgi/en-nut-discussion
>