[En-Nut-Discussion] Ethernet Failure

JOhan ferouskain argaelgr at yahoo.gr
Wed Dec 10 08:19:52 CET 2008


  Hello , i solved the problem  i had with the ethernet set up , i  followed your leads and rebuilded my  libraries for 1.3 .f and also i checked my makefiles and userconf and found out that since i migrated to newer nutos i ovewrited my userconf and   i had to remove the -D ETHERNUT 2 directive (now where did that came from ^^) from the userconf file ,  and substitute it with -D ethernut1 , worked like a charm   .
Thanks alot for your help .

Now i get some peculiar warnings though like implicit declaration of malloc , although my app works or another bizzare warnning is when i call inet_addr("192.168.1.1") arg 1 differs in 
singess  are the above warnings  normal ,r should i remove the -wall from gcc?

--- Στις Δευτ., 08/12/08, ο/η en-nut-discussion-request at egnite.de <en-nut-discussion-request at egnite.de> έγραψε:
Από: en-nut-discussion-request at egnite.de <en-nut-discussion-request at egnite.de>
Θέμα: En-Nut-Discussion Digest, Vol 62, Issue 7
Προς: en-nut-discussion at egnite.de
Ημερομηνία: Δευτέρα, 8 Δεκέμβριος 2008, 13:00

Send En-Nut-Discussion mailing list submissions to
	en-nut-discussion at egnite.de

To subscribe or unsubscribe via the World Wide Web, visit
	http://lists.egnite.de/mailman/listinfo/en-nut-discussion
or, via email, send a message with subject or body 'help' to
	en-nut-discussion-request at egnite.de

You can reach the person managing the list at
	en-nut-discussion-owner at egnite.de

When replying, please edit your Subject line so it is more specific
than "Re: Contents of En-Nut-Discussion digest..."


Today's Topics:

   1. SPI-Clock Ethernut 3 (Christoph Hillebrand)


----------------------------------------------------------------------

Message: 1
Date: Mon, 8 Dec 2008 10:29:23 +0100
From: "Christoph Hillebrand" <chr.hillebrand at online.de>
Subject: [En-Nut-Discussion] SPI-Clock Ethernut 3
To: <en-nut-discussion at egnite.de>
Message-ID: <000f01c95917$74f36d80$5eda4880$@hillebrand at online.de>
Content-Type: text/plain;	charset="iso-8859-1"

Hi all,

 

I work with Ethernut 3 Board, which has an AT91400008 MCU. I use
SPI-Bitbanging. 

Now it works nearly correct, but the clock signal is too low. I?ve got a
clock with a frequency of 20kHz and I need a frequency from 125 kHz to
4,8MHz. How could I adjust this frequency.

 

I would be very happy, if somebody could help me!

 

Best regards

 

Christoph



------------------------------

_______________________________________________
http://lists.egnite.de/mailman/listinfo/en-nut-discussion


End of En-Nut-Discussion Digest, Vol 62, Issue 7
************************************************



      
___________________________________________________________ 
Χρησιμοποιείτε Yahoo!; 
Βαρεθήκατε τα ενοχλητικά μηνύματα (spam); Το Yahoo! Mail 
διαθέτει την καλύτερη δυνατή προστασία κατά των ενοχλητικών 
μηνυμάτων http://login.yahoo.com/config/mail?.intl=gr 



More information about the En-Nut-Discussion mailing list